1. Home
  2. /
  3. Complete List of OBD2...
  4. /
  5. P0368 Code – What...

P0368 Code – What Does It Mean & How To Fix It

This is one of the most frequent OBD2 trouble codes. Read the full article below to know what it means, how to fix it, and what other codes may show related to it.

Definition

P0368 is the diagnostic error code DTC, indicating a specific problem in the Camshaft Position Sensor "B" Circuit High Input. This code is part of the On-Board Diagnostics II (OBD-II) system used in modern vehicles to monitor and report issues with various engine components.

Meaning

The P0368 code indicates that the Engine Control Module (ECM) has detected a higher-than-expected voltage signal from the Camshaft Position Sensor "B" circuit. This sensor is vital for the ECM to keep an eye on camshaft location and timing, a critical parameter in ensuring proper engine performance.


Causes

A P0368 code may be caused by several circumstances, such as:

  • Wiring or connection issues in the circuit for the Camshaft Position Sensor "B"; a broken Camshaft Position Sensor "B."
  • A camshaft that is faulty or damaged.
  • Issues with the timing chain or belt.
  • Rarely, there are ECM problems.

Symptoms

Common symptoms associated with a P0368 code may include:

  • Illumination of the Check Engine Light (CEL) on the dashboard.
  • Reduced engine performance or power.
  • Poor fuel efficiency.
  • Engine misfires or rough idling.
  • Stalling or difficulty starting the engine.

Diagnosis

A mechanic or technician will often take the following actions to troubleshoot a P0368 code:

  • To get the code and any associated codes, use an OBD-II scanner.
  • Look for any obvious damage to the Camshaft Position Sensor "B" and its connections.
  • Check the voltage and resistance of the sensor to see if it is operating properly.
  • Examine the camshaft and timing parts for wear and good alignment.
  • To see whether the problem reappears, clear the code and give it a test run.

Common mistakes

Common mistakes when dealing with a P0368 code include:

  • Replacing the sensor without checking the wiring and connectors for issues.
  • Neglecting to inspect the camshaft and timing components for problems.
  • Assuming the code is solely caused by a faulty sensor without considering other potential causes.

How serious is this?

Because the P0368 code may lead to reduced engine performance, poor fuel economy, and possible engine damage if left unresolved, it should be fixed without delay. It is advisable to have the car checked and repaired as quickly as possible, even though it may still be capable of driving.

What repairs can fix the codeS?

Repair manuals

Repairs for a P0368 code may include:

  • Replacing the Camshaft Position Sensor "B" if it's found to be faulty.
  • Repairing or replacing damaged wiring or connectors in the sensor circuit.
  • Realigning or replacing the camshaft if it's found to be damaged or misaligned.
  • Addressing any issues with the timing belt or chain.
  • In rare cases, replacing the ECM if it's determined to be the source of the problem.

Related codes

Related codes may include:

  • P0360 - Camshaft Position Sensor "B" Circuit Malfunction.
  • P0361 - Camshaft Position Sensor "B" Circuit Range/Performance.
  • P0362 - Camshaft Position Sensor "B" Circuit Low Input.
  • P0363 - Camshaft Position Sensor "B" Circuit High Input.
  • P0364 - Camshaft Position Sensor "B" Circuit Intermittent.

Conclusion

The DTC code P0368 indicates that the voltage level in the Camshaft Position Sensor "B" circuit is exceeded, which may have an impact on engine performance and efficiency. In order not to damage the vehicle again and ensure proper operation of the vehicle, timely diagnostics and repairs are necessary. Depending upon the particular cause of this code, repairs may include sensor replacement, wire replacements, camshaft inspection, or timing component modifications.

P0368 code – what does it mean & how to fix it

DOWNLOAD

A PDF VERSION OF THIS ARTICLE FOR LATER