1. Home
  2. /
  3. Complete List of OBD2...
  4. /
  5. P0005 Code – What...

P0005 Code – What Does It Mean & How To Fix It

This is one of the most frequent OBD2 trouble codes. Read the full article below to know what it means, how to fix it, and what other codes may show related to it.


P0001 is an OBDII generic code which means the powertrain control module detected a problem in the fuel volume regulator circuit. Fuel Volume Regulator Control Circuit/Open.


P0001 affects all fuel injection engines that have the type of fuel pressure regulator that is connected to this wiring harness. P0001 can also mean that one or more of your fuel injectors are not operating properly, P0001 is not an isolated error. P0001 will have to be pinpointed to determine the cause of the malfunction in your vehicle’s fuel system.

The P0001 code is a generic description of a problem with the circuit that extends from your engine computer (ECM) to your fuel pressure regulator on your fuel injection rail on your engine. P0001 also means there is an electrical issue with the circuit which sends a signal from your engine computer to your fuel pressure regulator on your fuel injection rail, essentially it means there is a problem in the electrical circuit that connects your ECM and fuel pressure regulator.


Possible causes of the P0001 trouble code include but are not limited to:

Often a faulty fuel pressure regulator, wiring harness and/or connectors. 

Fuel injectors can also cause P0001, so can dirty or corroded fuel pressure regulator connections.

Poor connections at the electrical connector(s) for the fuel pump module or damaged one.

Physical damage or corrosion on the fuel delivery system including the fuel tank, lines, fittings and seals. The part will need replacement if any internal debris is detected in any portion of this system.

Faulty PCM (engine control unit) only when diagnosed via freeze frame data. If there was no problem with freeze frame data then suspect a physical problem with wiring harnesses, connectors and/or components in the powertrain control module


Symptoms of a P0001 DTC (diagnostic trouble code) include:

  • During driving, the engine’s capabilities
  • The engine may stall.
  • The Check Engine Light (CEL)
  • The exhaust may appear to be smoking in a variety of hues, from black to white.
  • The efficiency of fuel economy will be poor.


P0001 is identified by a scan tool that can obtain sensor readings (not just one from an auto parts store). The data from the scan tool may be read by a trained expert to determine when the failure occurred or whether it still occurs. They may clear the code/light and drive the car to check for any return.

Depending on the test parameters, possibly clearing the code and doing a road test, further evaluation may be required. Multiple electrical instruments might be utilized for diagnosis, including:

  • The ECM data values can be inspected using an advanced scan tool.
  • With attachments, a digital voltage meter
  • A tester device that checks the fuel pressure.

Common mistakes

Replacing the fuel pump module without also checking the wiring harness connections.

Ignoring physical damage or corrosion on the fuel delivery system including the fuel tank, lines, fittings and seals. The part will need replacement if any internal debris is detected in any portion of this system

Failing to clean and inspect all connectors and components (the entire electrical circuit) when diagnosing P0001

How serious is this?

The P0001 error code might cause your car to stop running, and you may experience the following symptoms: Your Check Engine light may be on. Your car might stop producing power and stalling. The engine could make unusual sounds, such as a rattling noise.

This error will affect your fuel economy and emissions (if equipped). These problems can also get worse over time if the issue isn’t fixed immediately. Repairing the P0001 code will restore your engine to its proper operating condition.

If you ignore this warning and continue to drive with the P0001 trouble code stored in your system, it is likely that other components (like catalytic converters) will fail and cause more serious problems which require repairs that are much more expensive than diagnosing and repairing the problem once with a professional mechanic.

What repairs can fix the codeS?

  • Replace the fuel volume regulator.
  • Repair the wiring that connects to the ECM and fuel pressure regulator.
  • Replace damaged components in your vehicle’s fuel system, including: The injector, The injector wiring, Fuel pump and ECM

Related codes

P0001 affects the performance of your fuel delivery system and it can put added stress on other engine components because of this too much stress can lead to P0007, P0013, P0011, P0012, P0016 DTC’s and or P0002, P0003, or P0004.

How much does it cost to fix the P0001 code?

The cost to diagnose and repair the P0001 code can cost as much as $100 or more at a garage or dealership. Replacing components such as the fuel pressure regulator is around $300 for parts and labor on average.


The P0001 fault code is a concern and so it should be taken seriously. If left unaddressed, it can cost you much more money in the long term by causing damage to other components such as the catalytic converter which is about $1,500 to replace one.

It can also affect your fuel economy negatively. A professional technician will be able to diagnose and repair based upon the equipment that they have available at their shop or dealership with proper tools and data readings from a scan tool capable of reading sensor values. Don’t replace the fuel pressure regulator without performing diagnostic tests first!

P0005 code – what does it mean & how to fix it